Vallas Composite MálagaComposite & timber fencing
Dark vertical textured slats screwed to rails beside a block pillar
Installation guide

Expansion gaps in composite fences

Composite boards grow and shrink with temperature. On a hot Costa del Sol afternoon that movement is real, and a fence built without room for it will show it. Here is why gaps matter.

Technical guidesLast reviewed: Bauman Raymond Attila

Why do composite boards move?

In short: the plastic in composite expands when heated and contracts when it cools; the wood fibre reduces this but does not stop it.

The US Forest Products Laboratory sums it up: most plastics expand when heated, and adding wood decreases thermal expansion. That is one reason composite is more stable than unfilled plastic lumber – but it still moves more than many owners expect, and more than aluminium or masonry next to it.

Composite also takes up some moisture, which the same source notes increases with wood content. Temperature is the bigger factor on a sunny fence, but both add to the movement a fixing system must allow for.

If you are new to the material, start with what composite fencing is.

Where do the gaps go?

In short: at board ends, between boards and fixed elements, and around fixings – exactly where the manufacturer's instructions specify.

Every system is different, so we do not give generic figures. The places where movement needs room are, however, the same in most systems:

  • Board ends inside post channels or against pillars, where the board grows in length
  • Bottom and top of vertical boards, against the ground, wall top or cap
  • Around screws or clips, which some systems require to be oversized or slotted
  • Junctions with other materials such as rendered walls or metal frames

The size of each gap depends on the board, its length, and sometimes the temperature on the day of installation. The manufacturer's installation guide is the reference; we follow it on every job.

Brown composite slat fence on a rendered wall
Brown composite slat fence on a rendered wall

What goes wrong without gaps?

In short: boards bow, pop out of channels, crack at fixings or push against posts and pillars.

A board that cannot grow in length has to go somewhere. In a horizontal slot-in system it bows outwards or pushes the posts apart. In a vertical system, a board cut tight between ground and cap can buckle. Screws that pin a board rigidly can crack it as it moves. In the opposite case – boards fitted on a very hot day without allowance for contraction – gaps can open at the ends when it cools.

These problems often appear only in the first summer, which is why owners sometimes blame the material rather than the fitting. Our article on what can go wrong while building a composite fence covers this and other common faults.

How do we design a fence for movement?

In short: suitable board lengths, the right channels or clips, caps that hide gaps, and no rigid connections to walls.

Good detailing makes movement invisible. Post channels deep enough to hide a gap at each end, caps and trims that cover movement joints, and clips or slotted fixings that hold a board without pinning it all contribute.

We also avoid mixing materials rigidly: a composite board screwed directly into a rendered pillar on both ends has nowhere to move. In a composite fence on a low wall we use channels or brackets that let the board slide, and in a vertical composite fence we keep the board ends clear of ground and cap.

Does colour change how much boards move?

In short: darker boards absorb more solar heat, so in direct sun they generally get hotter – and heat drives movement.

A dark board in full afternoon sun gets hotter than a light one in the same position, simply because it absorbs more sunlight. Hotter boards expand more. This is one reason we discuss colour together with orientation; a very dark fence facing south or west deserves particular care with gaps. Our guide on composite in strong sun goes further.

What can owners check after installation?

In short: look for bowing boards, boards riding out of channels, cracks around screws and caps that have lifted.

A quick walk along the fence after the first hot spell tells you a lot. Small, even gaps at board ends are normal. Boards that bow, lift out of their channels or crack around fixings are not. If you see these on a fence we built, tell us; on an older fence, they usually point to fitting rather than the material itself.

Official sources

BR
Bauman Raymond Attila
Author and person responsible · Last reviewed:
FAQ

Frequently asked questions

Do composite boards really expand?

Yes. The plastic part of the material expands with heat. Wood fibre reduces the movement compared with pure plastic but does not eliminate it.

How big should the gap be?

It depends on the board system and length; the manufacturer's installation guide gives the figure. We do not use generic gap sizes.

Why are my composite boards bowing?

Usually because they were fitted without enough room to expand, or because posts are too far apart for the system. Moisture uptake can also contribute.

Will gaps be visible?

Good systems hide end gaps inside post channels or under caps. Gaps between boards are part of some designs.

Does the temperature on installation day matter?

Some manufacturers adjust gap sizes for installation temperature. We check the instructions for that.

Can composite be screwed directly into a wall?

Rigid fixing at both ends leaves no room for movement. We use channels, brackets or fixings that let the board move.

Do dark boards move more?

In direct sun, darker boards absorb more heat and so generally get hotter, which increases movement.

Do timber boards need gaps too?

Timber moves mainly with moisture rather than heat. Gaps between timber boards allow for swelling and help them dry.

Can a bowed board be fixed?

Sometimes it can be refitted with the correct gap if it has not deformed permanently. Otherwise it should be replaced.

Does moisture affect composite movement?

Composite absorbs some moisture, more with higher wood content, according to the US Forest Products Laboratory. Temperature is usually the bigger factor on fences.

Get a quote

Planning a composite or timber fence?

Send photos and the approximate length by WhatsApp or the form. We reply with what to check and an itemised quote, no commitment.