Vallas Composite MálagaComposite & timber fencing
Dark vertical textured slats screwed to rails beside a block pillar
Upright board fences

Vertical composite fencing

Turning the boards upright changes the look and the way a fence is built. Vertical composite fencing gives a contemporary, taller-looking screen and copes well with sloping gardens.

A vertical composite fence is a fence in which wood-plastic composite boards stand upright, fixed with screws or clips to horizontal rails that span between posts or pillars.

How is a vertical composite fence different?

In short: the boards stand upright on horizontal rails, instead of sliding horizontally into post channels.

In a horizontal system, each board spans from post to post. In a vertical system, two or more horizontal rails span between the posts, and the boards are fixed to the face of the rails – usually with screws or concealed clips – side by side, with or without gaps.

This has practical effects. Each board is short and supported at several points, so long spans between posts depend on the rails rather than on the boards. The top line can be level or follow the ground. Gaps between boards can be tuned for more air or more privacy.

The photo shows a vertical slatted fence with the boards screwed to rails beside a block pillar.

Dark vertical textured slats screwed to rails beside a block pillar
Dark vertical textured slats screwed to rails beside a block pillar

Why choose vertical boards?

In short: for a contemporary look, easier stepping on slopes and more freedom with gaps and heights.

Owners choose vertical boards mainly for appearance: upright lines look modern, make a fence seem taller and suit minimal architecture. There are practical reasons too:

  • Sloping ground: the boards can follow the slope while the rails step, avoiding large triangular gaps under the fence.
  • Variable openness: boards can be closed for privacy or spaced for airflow.
  • Mixed materials: rails can run between rendered or block pillars, combining with an existing wall.

The main drawback is the number of fixings – every board is fixed to every rail – so the quality of the fixing work shows. Our article on mistakes when choosing composite fencing covers the details owners overlook.

Why do rails and fixings matter so much?

In short: vertical boards hang on their rails, so the rails must be stiff and straight, and the fixings must allow the boards to move.

Composite expands and contracts with temperature. In a vertical fence most of that movement is along the length of each board, up and down. Fixings that are too tight, or boards cut to touch the ground or the cap, can bow or crack. We follow the manufacturer's instructions for fixing positions and gaps, and keep the bottom ends clear of soil.

The rails themselves – usually aluminium or steel profiles – need to be stiff enough for the span, or the fence will sag between posts. Our guide on expansion gaps explains how movement works without quoting generic figures.

What should you check first?

In short: the boundary, height rules, community style rules and whether the ground will be stepped or followed.

  • Boundary and neighbour: agree the line and which side faces whom; vertical fences often look different from each side.
  • Rules: the *ayuntamiento* and, where relevant, the community set heights and permitted designs.
  • Slope: decide whether you want a level top in steps or a top that follows the ground.
  • Combination with walls: if the rails will run between existing pillars, those pillars must be sound. See composite on a low wall.

What upkeep does a vertical fence need?

In short: occasional washing, keeping soil away from the board ends and checking fixings along the rails.

Vertical boards shed rain well, but dirt collects on the rails and at the bottom ends. A wash from top to bottom and a look at the fixings once a year is usually enough. See cleaning and stains for how to treat marks without damaging the surface.

What affects the cost?

In short: length, height, rail system, board spacing, posts or pillars, the slope and the access – each itemised.

Vertical systems use more fixings and often more rails than horizontal ones, and closely spaced boards use more material. On slopes the setting out takes longer. The factors are listed below; general quote advice is on presupuestovalla.eu.

BR
Bauman Raymond Attila
Author and person responsible · Last reviewed:
How we build it – step by step

How we build it – step by step

  1. Setting out

    We mark the line, posts and rail heights, and decide with you how the fence will treat the slope.

  2. Clearing and removal

    We clear the line and remove any old fence included in the job.

  3. Footings or pillars

    We set posts in concrete footings or prepare existing pillars to receive the rails.

  4. Rails

    We fix the horizontal rails level and straight between the posts or pillars.

  5. Boards

    We fix the upright boards to every rail with the spacing and movement gaps the system requires.

  6. Caps and trims

    We fit top caps or trims and check the line along the whole fence.

  7. Cleaning and handover

    We clean the site and hand over, with photos for owners abroad.

When is it the right choice – and when not?

When is it the right choice – and when not?

A good fit if…

  • Contemporary houses and minimal gardens
  • Sloping gardens where stepping is needed
  • Combining rails with existing sound pillars
  • Owners who want to tune privacy and airflow

Consider another option if…

  • Owners who prefer the classic horizontal look of the area
  • Pillars that are cracked or not plumb
  • Places where community rules require horizontal infill
  • Very tight budgets where fixings and rails add work
What affects the cost?

What affects the cost?

We don't publish fixed prices: every fence is quoted line by line using these factors.

  • Linear metres and height
  • Rail system and number of rails
  • Board spacing: closed or slatted
  • Posts in footings or existing pillars
  • Slope and stepping
  • Composite board system and colour
  • Access to the site
  • Removal of an old fence and clearing
  • Licence or declaración responsable, if required

Fence cost calculator See how a fence quote is put together

Itemised quoteItemisedquoteLinear metresHeightPanel typeLow wall or notFoundationsGround & slopeAccessOld fence removalClearingPermit
FAQ

Frequently asked questions

Are vertical composite fences stronger than horizontal ones?

Not inherently. Strength depends on the posts, rails and footings. Vertical boards are well supported because they are fixed to several rails.

Can I see the screws?

Some systems use visible screws, others concealed clips. We discuss the fixing type when choosing the boards.

Do vertical fences work on slopes?

Yes, that is one of their advantages. The boards can follow the ground while the rails step, avoiding gaps under the fence.

Can you fix rails between my existing pillars?

Often yes, if the pillars are sound and plumb. We check them first.

Can the boards have gaps?

Yes. Gaps let air through and soften the look, but reduce privacy. Many owners choose small gaps as a compromise.

Will vertical boards bow in the heat?

Composite expands in heat, so fixing positions and end gaps must follow the manufacturer's instructions. Correctly fixed boards should not bow.

Are the rails visible?

From the rail side, yes. Some designs put boards on both sides or use a cover strip; we agree which side faces you.

Is a vertical fence harder to clean?

Not really. Rain runs down vertical boards; dirt collects mainly on the rails and the bottom ends.

Can a vertical fence go on a low wall?

Yes, the rails can run between pillars standing on a murete, combining the solid base with the vertical look.

How do I start?

Send photos of the line, a note on the slope and the approximate length. We will prepare an itemised quote with no commitment.

Get a quote

Planning a composite or timber fence?

Send photos and the approximate length by WhatsApp or the form. We reply with what to check and an itemised quote, no commitment.